Brocade Communications Systems 300 Guide d'installation

53-1000862-0808 May 2015Brocade 300Hardware Installation Guide

What’s new in this document10 Brocade 300 Hardware Installation Guide53-1000862-08

Brocade 300 Introduction● Brocade 300 features...11

Facility requirementsThe following table provides the facilities requirements that must be met for the Brocade 300.Facility RequirementsTABLE 1 Type

FIGURE 2 Trunking port groups and port numbers of the Brocade 3001. Trunking port group 1: FC ports 00-072. Trunking port group 2: FC ports 08-153. Tr

For detailed information on enabling additional ports using the POD license, refer to the Fabric OSAdministrator’s Guide .ISL trunking groupsThe Broca

Brocade 300 Installation and Configuration● Items included with the Brocade 300...

General precautionsDANGERThe procedures in this manual are for qualified service personnel.CAUTIONChanges or modifications made to this device that ar

CAUTIONEnsure that the airflow direction of the power supply unit matches that of the installed fantray. The power supplies and fan trays are clearly

• Plan for rack space required for cable management before installing the switch.• Leave at least 1 m (3.28 ft) of slack for each port cable. This pro

• To allow the port side of the switch to slide out of the exhaust-air side of the rack. In this installation,the port side of the switch is flush wit

© 2015, Brocade Communications Systems, Inc. All Rights Reserved.ADX, Brocade, Brocade Assurance, the B-wing symbol, DCX, Fabric OS, HyperEdge, ICX, M

Parameter ValueBits per second 9600Data bits 8Parity NoneStop bits 1Flow control None• In a UNIX environment, enter the following string at the prompt

Date and time settingsThe Brocade 300 maintains the current date and time inside a battery-backed real-time clock (RTC)circuit. Date and time are used

The tsClockServer command accepts multiple server addresses in either IPv4, IPv6, or DNS nameformats. When multiple NTP server addresses are passed, t

The following procedure describes how to set the current time zone usinginteractive mode to Pacific Standard Time.1. Type the tsTimeZone command as fo

Synchronizing local time using NTP24 Brocade 300 Hardware Installation Guide53-1000862-08

Brocade 300 Operation● Powering the Brocade 300 on and off...25● Interpretin

FIGURE 4 Detailed View, Brocade 300 LEDsA. System status LED (green/amber)B. System power LED (green)C. Link status LEDD. Link speed LEDE. Port status

Brocade 300 LED Patterns During Normal Operation (Continued)TABLE 2 LED Name LED Color Status of Hardware Recommended ActionSteady amber (formore th

Brocade 300 LED Patterns During Normal Operation (Continued)TABLE 2 LED Name LED Color Status of Hardware Recommended ActionSteady amber (formore th

1. Verify that the switch LEDs indicate that all components are healthy.See the LED patterns section for descriptions and interpretations of LED patte

ContentsPreface...5D

FIGURE 5 Installing an SFP in the upper row of port slotDiagnostic testsIn addition to POST, the Fabric OS includes diagnostic tests to help you troub

Managing the Brocade 300You can use the management functions built into the Brocade 300 to monitor the fabric topology, portstatus, physical status, a

Managing the Brocade 30032 Brocade 300 Hardware Installation Guide53-1000862-08

Brocade 300 SAN Switch Technical SpecificationsThe Brocade 300 SAN Switch is a cost-effective and highly-scalable 1, 2, 4, or 8 Gbps switch, designedf

EthernetSystem component DescriptionEthernet management port RJ-45LEDsSystem component DescriptionSwitch status andmanagementOne system status LED (ab

Condition Operational Non-operationalAltitude (above sealevel)0 to 3000 m (10,000 feet) 0 to 12000 m (39,000 feet)Shock 20 G, 6 ms, half-sine wave 33

Fibre Channel data transmission rangesPort speed (Gbps) Cable size(microns)Short wavelength(SWL)Long wavelength(LWL)Extended longwavelength (ELWL)1 50

Pin Signal Description5 GND Logic ground6 UART1_RXD Receive data7 Not supported N/A8 Not supported N/ASerial port specifications (protocol)Parameter V

Regulatory compliance (safety)• CAN/CSA-C22.2 No. 60950-1-07/UL60950-1 - Safety of Information Technology Equipment• EN 60825-1 Safety of Laser Produc

Regulatory Statements● BSMI statement (Taiwan)...39● Cana

Boot...28Interpreting POST results...

‐ EN61000-3-2/JEIDA (European and Japanese Harmonics Spec)‐ EN61000-3-3China CC statementChina ROHSRefer to the latest revision of the China ROHS docu

FCC warning (US only)This equipment has been tested and complies with the limits for a Class A computing device pursuantto Part 15 of the FCC Rules. T

VCCI statement42 Brocade 300 Hardware Installation Guide53-1000862-08

Cautions and Danger Notices● Cautions...

PRECAUCIÓN Asegúrese de que el flujo de aire en las inmediaciones de las partes anterior, laterales yposterior del instrumento no esté restringido.CAU

MISE ENGARDEAvant de brancher un câble à un port, assurez-vous de décharger la tension du câble enreliant les contacts électriques à la terre.PRECAUCI

DANGER Vérifiez que les circuits de sources d'alimentation sont bien mis à la terre, puis utilisez lecordond'alimentation fourni avec le dis

Dangers related to equipment weightDANGERMake sure the rack housing the device is adequately secured to prevent it from becomingunstable or falling ov

Danger Notices48 Brocade 300 Hardware Installation Guide53-1000862-08

Preface● Document conventions...5● Brocade resource

Convention Description[ ] Syntax components displayed within square brackets are optional.Default responses to system prompts are enclosed in square b

Brocade resourcesVisit the Brocade website to locate related documentation for your product and additional Brocaderesources.You can download additiona

• Brocade Supplemental Support augments your existing OEM support contract, providing directaccess to Brocade expertise. For more information, contact

About This Document● Supported hardware and software..................... 9● What’s new