Brocade Communications Systems 8/80 Manuel de service Page 17
- Page / 62
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Switching and Routing
May 2012 © 2012 Brocade Communications Systems, Inc. 2 - 9
ServerIron(config-vlan-10)# untag ethernet 1/1 to 1/24
ServerIron(config-vlan-10)# untag ethernet 2/1 to 2/2
ServerIron(config-vlan-10)# uplink-switch ethernet 2/1 to 2/2
In this example, 24 ports on a 10/100 module and two Gigabit ports on a Gigabit module are added to port-based
VLAN 10. The two Gigabit ports are then configured as uplink ports.
Syntax: [no] uplink-switch ethernet <portnum> [to <portnum> | ethernet <portnum>]
Setting a Priority for a VLAN
When you assign a higher priority to a VLAN so that in times of congestion, it will receive precedence over other
transmissions. To do this, enter commands such as the following:
ServerIron(config)#vlan 25
ServerIron(config-vlan-25)#priority high
Syntax: [no] priority normal | high
Configuring an AppleTalk Protocol VLAN
You can create an AppleTalk protocol VLAN within a ServerIron port-based VLAN when entered at the VLAN
Level. All ports are assumed by default to be members of the VLAN when initially created.
To create an AppleTalk Protocol VLAN with permanent port membership of 9 and 13 and no dynamic ports within
an already defined port-based VLAN 2, enter commands such as the following:
ServerIron(config)#vlan 2
ServerIron(config-vlan-2)#atalk-proto
ServerIron(config-vlan-atalk-proto)#static e 9 e 13
ServerIron(config-vlan-atalk-proto)#no dynamic
If configuring this on a switch, enter vlan 2 by port at the CONFIG Level versus vlan 2, as shown in the example.
Protocol VLAN membership can be modified using the dynamic, static, or exclude commands.
To specify a VLAN name, use the name keyword followed by a string. The name keyword and string are the last
arguments in the command. For example, to name an AppleTalk VLAN:
ServerIron(config)#atalk-proto name AppleVLAN1
To name an IP VLAN:
ServerIron(config)#ip-proto 192.75.5.0/24 name "Ship and Recv"
This example shows how to specify a name that contains a blank. Use double quotation marks before and after
the name.
Syntax: [no] atalk-proto [<name>]
The <name> can be up to 16 characters long and can contain blanks.
Configuring a Decnet Protocol VLAN
You can create a Decnet protocol VLAN within a ServerIron port-based VLAN, when entered at the VLAN Level.
All ports are assumed by default to be members of the VLAN when initially created.
To create a Decnet protocol VLAN with permanent port membership of 15 and 16 with port 17 as dynamic
member port, within VLAN 5, enter the following commands.
ServerIron(config)#vlan 5
ServerIron(config-vlan-5)#decnet-proto
ServerIron(config-vlan-decnet-proto)#exclude e 1 to 14 e18
If configuring this on a switch, enter vlan 5 by port at the CONFIG Level versus vlan 5, as shown in the example
above.
Protocol VLAN membership can be modified using the dynamic, static, or exclude commands.
- ServerIron Traffic Works 1
- Contents 3
- Chapter 1 7
- About this Guide 7
- Getting technical help 8
- Document feedback 8
- Chapter 2 9
- Static MAC Entries 10
- Displaying MAC Addresses 10
- Configuring Fast Port Span 11
- Configuring Fast Uplink Span 11
- Trunk Groups 14
- Changing the Tag Type 15
- Enabling Aggregated VLAN 15
- Configuring Uplink Ports 16
- Setting a Priority for a VLAN 17
- Dual-Mode VLAN Ports 20
- MAC Filters 22
- Setting the MAC Age Time 24
- Address-Lock Filters 25
- Setting the Broadcast Limit 26
- Assigning a Gateway List 26
- Multicast 27
- Adding an IP Interface 28
- Adding a Static IP Route 30
- Adding a Static ARP Entry 30
- Clearing the ARP Cache 31
- Clearing the IP Cache 31
- Setting System Max 31
- Adding a Static MAC Address 32
- Displaying the IP Host Table 34
- Displaying Static ARP Entries 36
- Displaying the IP Route Table 37
- Disabling Layer 2 Switching 40
- Configuring an IP Interface 40
- Configuring an IP Filter 41
- SLB Example 42
- TCS Uses of Filters 42
- Setting the TTL 43
- Enabling RIP 44
- RIP Timers 45
- Enabling Redistribution 46
- Denying Redistribution 46
- Permitting Redistribution 47
- Learning RIP Default Routes 48
- Dynamic Link Aggregation 49
- Valid Aggregate Links 50
- Flexible Trunk Eligibility 52
- Enabling Link Aggregation 53
- Link Aggregation Parameters 55
- About Blocked Ports 57
- Switching and Routing 61
- Syntax: clear link-aggregate 61
Produits connexes et manuels pour Commutateurs de réseau Brocade Communications Systems 8/80
Commutateurs de réseau Brocade Communications Systems ServerIron ADX 12.4.00 Manuel de service
(188 pages)
(188 pages)
(64 pages)
Commutateurs de réseau Brocade Communications Systems Encryption Switch Manuel de service
(326 pages)
(326 pages)
Commutateurs de réseau Brocade Communications Systems Brocade VDX 6710-54 Manuel d'utilisateur
(8 pages)
(8 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.899 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels