Brocade Communications Systems LS-STK Guide d'installation Page 55
- Page / 94
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Brocade FastIron LS and FastIron LS-STK Hardware Installation Guide 45
53-1002187-01
Configuring IP addresses
4
DRAFT: BROCADE CONFIDENTIAL
FIGURE 34 Installing a fiber optic module
Cabling a fiber optic module
1. Remove the protective covering from the fiber optic port connectors and store it for future use.
2. Before cabling a fiber optic module, Brocade strongly recommends cleaning the cable
connectors and the port connectors. For more information, see “Cleaning the fiber-optic
connectors” on page 45.
3. Gently insert the cable connectors (a tab on each connector should face upward) into the port
connectors until the tabs lock into place.
4. Observe the link and active LEDs to determine if the network connections are functioning
properly. For more information about the LED indicators, see Table 13 on page 46.
Cleaning the fiber-optic connectors
To avoid problems with the connection between the fiber optic module (SFP (mini-GBIC) or XFP) and
the fiber cable connectors, Brocade strongly recommends cleaning both connectors each time you
disconnect and reconnect them. In particular, dust can accumulate in the connectors and cause
problems such as reducing the optic launch power.
To clean the fiber cable connectors, Brocade recommends using the fiber optic reel-type cleaner
that shipped with your FastIron LS. You can also purchase this type of cleaner from the following
Website:
http://www.fisfiber.com/Home_Page.asp
When not using an SFP or XFP connector, make sure to keep the protective covering on.
1CX4 fiber optic module
1
- Brocade FastIron LS and 1
- Document History 2
- Contents 3
- About This Document 7
- Notice to the reader 8
- Related publications 9
- DRAFT: BROCADE CONFIDENTIAL 10
- Product Overview 11
- Control features 12
- Network interfaces 13
- 53-1002187-01 14
- Fiber optic modules 17
- Power supplies 17
- 100-240V~ 18
- 50-60Hz 2A 18
- RPS DC In 12V 13A 18
- Unpacking a system 19
- Summary of installation tasks 20
- Installation precautions 21
- Lifting precautions 22
- Power precautions 22
- Cabling infrastructure 23
- Installation location 23
- Installing the device 23
- Desktop installation 24
- Rack mount installation 24
- Connecting devices in a stack 25
- Package contents 28
- Installation 29
- Selecting a site 29
- Equipment checklist 30
- Mounting 30
- Desktop or shelf mounting 32
- Ports pin-out (RPS2-EIF) 34
- Installing an SFP transceiver 36
- Powering on the system 36
- Verifying proper operation 37
- Attaching a PC or terminal 37
- Wiring map for serial cable 38
- Series Devices 39
- Upgrading software 45
- Assigning permanent passwords 47
- Configuring IP addresses 49
- Connecting network devices 52
- Connectors 52
- Cable specifications 52
- Cabling a fiber optic module 55
- Testing connectivity 56
- Using the temperature sensor 59
- Displaying the temperature 59
- Hardware maintenance schedule 63
- Digital optical monitoring 66
- Troubleshooting 67
- In-band access 68
- Hardware Specifications 69
- Operating environment 70
- Storage environment 70
- Mean Time Before Failure 70
- Fastlron LS 71
- Regulatory compliance 72
- Warranty 73
- Pinouts and signaling 73
- AC power supply 76
- Power cables 76
- Key features 77
- FCC CFR 47 Part 15 warning 78
- CISPR 22 CLASS A warning 78
- Safety warnings 78
- Environmental considerations 79
- Regulatory Statements 81
- Japan power cord 82
- Caution and Danger Notices 85
Produits connexes et manuels pour Mise en réseau Brocade Communications Systems LS-STK
(43 pages)
(86 pages)GE 45144 GE Choice Alert Key-chain Remote manuály
Uživatelské manuály a uživatelské příručky pro Senzory GE 45144 GE Choice Alert Key-chain Remote.
Poskytujeme 1 manuály pdf GE 45144 GE Choice Alert Key-chain Remote ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels