Brocade Communications Systems 8/80 Manuel de service Page 108
- Page / 133
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
84 Fabric Watch Administrator’s Guide
53-1002153-01
Switch monitoring
8
Switch status policy planning
Fabric Watch monitors the health of the switch under various classes. Table 28 lists the current
overall switch status policy parameters in a switch and identifies the factors that affect their health.
Note that not all switches use the listed monitors.
NOTE
The default setting for a MARGINAL state is 0, which prevents Fabric Watch from generating
notifications due to missing power supplies. For configurations with a 2+2 power suppy
combination, we recommend you change the default Fabric Watch default setting of 0 to 2 power
supplies (PS), which forces the overall switch status to a MARGINAL state.
NOTE
Use the switchstatusPolicySet command to manually change the policy setting. Refer to the FOS
Command Reference Manual for more information.
Implementing your switch status policy
After you plan and define your switch status policy, implement it using the following procedure.
1. Enter the switchStatusPolicySet command to configure each policy.
Each policy has two parameters that can be configured: Marginal and Down.
2. Set the number of units Marginal or Down based on your system requirements for each policy
or parameter.
TABLE 28 Switch status policy factors
Monitor Health factors
Power Supplies Power supply thresholds detect absent or failed power supplies, and power supplies that are
not in the correct slot for redundancy.
The presence of four or more FS8-18 encryption blades in the DCX Data Center Backbone
causes the Fabric Watch switch status policy for power supplies to assume a policy setting
of 2,1, as with the blades listed above. Use the switchStatusPolicySet command if you need
to manually change the policy setting.
Temperatures Temperature thresholds, faulty temperature sensors.
Fans Fan thresholds, faulty fans.
WWN Faulty WWN card (applies to modular switches).
CP Switch does not have a redundant CP (applies to modular switches).
Blades Faulty blades (applies to modular switches).
Core Blade Faulty core blades.
Flash Flash thresholds.
Marginal Ports
1
Port, E_Port, FOP_port (optical), and FCU_Port (copper) port thresholds. Whenever these
thresholds are persistently high, the port is Marginal.
Faulty Ports
1
Hardware-related port faults.
Missing SFPs
1
Ports that are missing SFP media.
Error Ports1 Ports with errors.
1
Marginal ports, faulty ports, error ports, and missing SFPs are calculated as a percentage of the physical ports
(excluding FCoE and VE_Ports).
- PRIMERGY 1
- 本書をお読みになる前に 2
- Document History 5
- Contents 7
- Chapter 7 Port Monitoring 10
- Chapter 8 System Monitoring 10
- About This Document 17
- What’s new in this document 19
- Document conventions 20
- Additional information 21
- Getting technical help 22
- Document feedback 23
- Fabric Watch 25
- Fabric Watch overview 26
- Role-based access control 26
- Fabric Watch licensing 26
- Monitoring 27
- Event behavior configuration 28
- Time base configuration 28
- Alert configuration 28
- Post-processing of messages 28
- Switch monitoring components 29
- Security monitoring 30
- SFP monitoring 30
- Port monitoring 30
- Port persistence 31
- Port fencing 31
- Logical switch support 32
- Fabric Watch event settings 33
- Triggered event behavior 34
- E-mail alert 35
- SNMP traps 35
- Fabric Watch audit messages 36
- Data values 37
- Fabric Watch Thresholds 39
- In-between buffer values 40
- Audit and RASlog messages 40
- Time bases 41
- Threshold triggers 42
- Fabric Watch alarm behavior 43
- Elements 46
- Class Description 47
- Fabric Watch Activation 49
- FIGURE 6 Example OID tree 53
- Fabric Watch Configuration 55
- Disabling an e-mail alert 58
- Enabling an e-mail alert 58
- Sending a test e-mail message 59
- Notification configuration 60
- FW: Alarms are enabled 61
- Area Description 64
- Fabric class default settings 65
- Security class areas 66
- Threshold state 67
- SFP class areas 69
- • Send an SNMP alarm 72
- • Log a RASlog message 72
- • Send an e-mail alert 72
- Configuration recommendation 73
- 16 Gbps and QSFP monitoring 74
- Monitoring the SFP and QSFP 75
- Security classes 78
- Port Monitoring 81
- Port class default settings 83
- Port configuration 84
- Port type: physical port 85
- E_Port class default settings 88
- • Area: Loss of Signal Count 90
- • Area: Link Reset 90
- Port fencing configuration 95
- Port fencing requirements 96
- Enabling port fencing 96
- Disabling port fencing 96
- • Link Reset (Fabric OS only) 97
- • Security (M-EOS) 97
- 53-1002153-01 100
- System Monitoring 101
- Resource class settings 103
- Using the nosave command 104
- Environment class settings 105
- CPU and memory 106
- Switch monitoring 107
- Switch status policy planning 108
- FRU monitoring 109
- FRU class areas 110
- Configuring FRUs 110
- Recommended FRU settings 111
- In this chapter 113
- System Monitor 114
- Configuring threshold traits 115
- Configuring threshold alarms 116
- Configuring alarms for FRUs 118
- Configuring alarm filters 118
- Displaying alarms 119
- E-mail notification 120
- Disabling the e-mail alert 121
- Fabric Watch Reports 123
- Switch Health report 125
- Switch Status Policy report 126
- Port Detail report 127
- Report item Description 128
- CA92344-0161-01 133
Produits connexes et manuels pour Commutateurs de réseau Brocade Communications Systems 8/80
(21 pages)© 2020, manymanuals.fr. Tous droits réservés | 2.462 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels