Brocade Communications Systems 8/80 Manuel de service Page 21
- Page / 133
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Fabric Watch Administrator’s Guide xix
53-1002153-01
What’s new in this document
Notes, cautions, and warnings
The following notices and statements are used in this manual. They are listed below in order of
increasing severity of potential hazards.
NOTE
A note provides a tip, guidance, or advice, emphasizes important information, or provides a
reference to related information.
ATTENTION
An Attention statement indicates potential damage to hardware or data.
CAUTION
A Caution statement alerts you to situations that can be potentially hazardous to you or cause
damage to hardware, firmware, software, or data.
DANGER
A Danger statement indicates conditions or situations that can be potentially lethal or extremely
hazardous to you. Safety labels are also attached directly to products to warn of these conditions
or situations.
Key terms
For definitions specific to Brocade and Fibre Channel, see the Brocade Glossary.
For definitions of SAN-specific terms, visit the Storage Networking Industry Association online
dictionary at http://www.snia.org/education/dictionary.
Additional information
This section lists additional Brocade and industry-specific documentation that you might find
helpful.
To get up-to-the-minute information, go to http://my.brocade.com to register at no cost for a user ID
and password.
White papers, online demonstrations, and data sheets are available through the Brocade website
at:
http://www.brocade.com/products-solutions/products/index.page
For additional Brocade documentation, visit the Brocade website:
http://www.brocade.com
Release notes are available on the MyBrocade website and are also bundled with the Fabric OS
firmware.
- PRIMERGY 1
- 本書をお読みになる前に 2
- Document History 5
- Contents 7
- Chapter 7 Port Monitoring 10
- Chapter 8 System Monitoring 10
- About This Document 17
- What’s new in this document 19
- Document conventions 20
- Additional information 21
- Getting technical help 22
- Document feedback 23
- Fabric Watch 25
- Fabric Watch overview 26
- Role-based access control 26
- Fabric Watch licensing 26
- Monitoring 27
- Event behavior configuration 28
- Time base configuration 28
- Alert configuration 28
- Post-processing of messages 28
- Switch monitoring components 29
- Security monitoring 30
- SFP monitoring 30
- Port monitoring 30
- Port persistence 31
- Port fencing 31
- Logical switch support 32
- Fabric Watch event settings 33
- Triggered event behavior 34
- E-mail alert 35
- SNMP traps 35
- Fabric Watch audit messages 36
- Data values 37
- Fabric Watch Thresholds 39
- In-between buffer values 40
- Audit and RASlog messages 40
- Time bases 41
- Threshold triggers 42
- Fabric Watch alarm behavior 43
- Elements 46
- Class Description 47
- Fabric Watch Activation 49
- FIGURE 6 Example OID tree 53
- Fabric Watch Configuration 55
- Disabling an e-mail alert 58
- Enabling an e-mail alert 58
- Sending a test e-mail message 59
- Notification configuration 60
- FW: Alarms are enabled 61
- Area Description 64
- Fabric class default settings 65
- Security class areas 66
- Threshold state 67
- SFP class areas 69
- • Send an SNMP alarm 72
- • Log a RASlog message 72
- • Send an e-mail alert 72
- Configuration recommendation 73
- 16 Gbps and QSFP monitoring 74
- Monitoring the SFP and QSFP 75
- Security classes 78
- Port Monitoring 81
- Port class default settings 83
- Port configuration 84
- Port type: physical port 85
- E_Port class default settings 88
- • Area: Loss of Signal Count 90
- • Area: Link Reset 90
- Port fencing configuration 95
- Port fencing requirements 96
- Enabling port fencing 96
- Disabling port fencing 96
- • Link Reset (Fabric OS only) 97
- • Security (M-EOS) 97
- 53-1002153-01 100
- System Monitoring 101
- Resource class settings 103
- Using the nosave command 104
- Environment class settings 105
- CPU and memory 106
- Switch monitoring 107
- Switch status policy planning 108
- FRU monitoring 109
- FRU class areas 110
- Configuring FRUs 110
- Recommended FRU settings 111
- In this chapter 113
- System Monitor 114
- Configuring threshold traits 115
- Configuring threshold alarms 116
- Configuring alarms for FRUs 118
- Configuring alarm filters 118
- Displaying alarms 119
- E-mail notification 120
- Disabling the e-mail alert 121
- Fabric Watch Reports 123
- Switch Health report 125
- Switch Status Policy report 126
- Port Detail report 127
- Report item Description 128
- CA92344-0161-01 133
Produits connexes et manuels pour Commutateurs de réseau Brocade Communications Systems 8/80
(21 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.404 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels