Brocade Communications Systems 8/80 Manuel de service Page 109
- Page / 133
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Fabric Watch Administrator’s Guide 85
53-1002153-01
FRU monitoring
8
The following example shows a switch status policy for temperature:
Bad Temperatures contributing to DOWN status: (0..10) [0] 3
Bad Temperatures contributing to MARGINAL status: (0..10) [0] 1
The following example shows a switch status policy for fans:
Bad Fans contributing to DOWN status: (0..3) [0] 2
Bad Fans contributing to MARGINAL status: (0..3) [0] 1
Switch status policies are saved in a nonvolatile memory, and therefore are persistent until
changed.
Viewing your switch status policy
After you have defined and configured your switch status policy, view it with the
switchStatusPolicyShow command. The switchStatusPolicyShow command displays the following
policy parameters that determine the overall switch status.
NOTE
FCoE and VE ports are not considered in marginal port or faulty port calculations.
• Power Supplies—The power supply thresholds detect absent or failed power supplies.
• Temperature—Temperature thresholds detect faulty temperature sensors.
• Fan—Fan thresholds detect faulty fans.
• Flash—Flash thresholds monitor flash memory.
• Marginal Ports—Ports that move into the marginal state for reasons such as insufficient buffer
credits.
• Port Persistence Time—Fabric Watch waits for the port persistence time duration before it
declares the port to be in MARGINAL state when it crosses the high threshold.
• Faulty Ports—Ports that are faulty because of hardware faults, such as invalid SFPs.
• Missing SFPs—Monitors the number of ports without SFPs.
• Error Ports—Ports that are disabled because of segmentation, an authentication failure, port
fencing, or bottleneck detection.
The policy you defined determines the output in the Switch Status Policy Report.
See Chapter 10, “Fabric Watch Reports,” for more details about the Switch Status Policy Report.
FRU monitoring
Supported FRU areas depend on the type of Brocade switch. For the following switches, the slot
and WWN areas are not supported:
• Brocade 300, 5100, and 5300 switches
• Brocade DCX and DCX-4S Data Center Backbone
• Brocade Encryption Switch
- PRIMERGY 1
- 本書をお読みになる前に 2
- Document History 5
- Contents 7
- Chapter 7 Port Monitoring 10
- Chapter 8 System Monitoring 10
- About This Document 17
- What’s new in this document 19
- Document conventions 20
- Additional information 21
- Getting technical help 22
- Document feedback 23
- Fabric Watch 25
- Fabric Watch overview 26
- Role-based access control 26
- Fabric Watch licensing 26
- Monitoring 27
- Event behavior configuration 28
- Time base configuration 28
- Alert configuration 28
- Post-processing of messages 28
- Switch monitoring components 29
- Security monitoring 30
- SFP monitoring 30
- Port monitoring 30
- Port persistence 31
- Port fencing 31
- Logical switch support 32
- Fabric Watch event settings 33
- Triggered event behavior 34
- E-mail alert 35
- SNMP traps 35
- Fabric Watch audit messages 36
- Data values 37
- Fabric Watch Thresholds 39
- In-between buffer values 40
- Audit and RASlog messages 40
- Time bases 41
- Threshold triggers 42
- Fabric Watch alarm behavior 43
- Elements 46
- Class Description 47
- Fabric Watch Activation 49
- FIGURE 6 Example OID tree 53
- Fabric Watch Configuration 55
- Disabling an e-mail alert 58
- Enabling an e-mail alert 58
- Sending a test e-mail message 59
- Notification configuration 60
- FW: Alarms are enabled 61
- Area Description 64
- Fabric class default settings 65
- Security class areas 66
- Threshold state 67
- SFP class areas 69
- • Send an SNMP alarm 72
- • Log a RASlog message 72
- • Send an e-mail alert 72
- Configuration recommendation 73
- 16 Gbps and QSFP monitoring 74
- Monitoring the SFP and QSFP 75
- Security classes 78
- Port Monitoring 81
- Port class default settings 83
- Port configuration 84
- Port type: physical port 85
- E_Port class default settings 88
- • Area: Loss of Signal Count 90
- • Area: Link Reset 90
- Port fencing configuration 95
- Port fencing requirements 96
- Enabling port fencing 96
- Disabling port fencing 96
- • Link Reset (Fabric OS only) 97
- • Security (M-EOS) 97
- 53-1002153-01 100
- System Monitoring 101
- Resource class settings 103
- Using the nosave command 104
- Environment class settings 105
- CPU and memory 106
- Switch monitoring 107
- Switch status policy planning 108
- FRU monitoring 109
- FRU class areas 110
- Configuring FRUs 110
- Recommended FRU settings 111
- In this chapter 113
- System Monitor 114
- Configuring threshold traits 115
- Configuring threshold alarms 116
- Configuring alarms for FRUs 118
- Configuring alarm filters 118
- Displaying alarms 119
- E-mail notification 120
- Disabling the e-mail alert 121
- Fabric Watch Reports 123
- Switch Health report 125
- Switch Status Policy report 126
- Port Detail report 127
- Report item Description 128
- CA92344-0161-01 133
Produits connexes et manuels pour Commutateurs de réseau Brocade Communications Systems 8/80
(21 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.281 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels